Using this tweeter and a Swans M5 N bass driver Bernd Timmermanns designed the Hora.
Unfortunately, the price EUR 50.00 quoted by Hobby HiFi is wrong. The correct price according to the distributor Expolinear is EUR 98.00 per unit.
The cabinet comprises a Helmholtz absorber to eliminate unwanted resonance.
Excerpt of the review by Hobby HiFi 6/2007: ..."The Hora reproduces a clear and natural sound we seldom experienced before. The optimal fusion of tweeter and bass driver is reflected in particular by an outstanding homogeneity of vocals. It's so easy to immerse into music, forgetting that there are loudspeakers. The three dimensional image is not spectacular, but displayed with such consummate ease that the listener won't even see the physical speaker anymore. Instead, all vocals and instruments are easy to pinpoint. These slim speaker have, obviously, limitations regarding the output level. But within these limitations the considerably low and detailed bass surprises. Also, the fundamental tone is exceptionally good, certainly due to the bass pull circuit." ... Our kit consists of: - Swans tweeter TN-28 with enclosure - Swans bass driver M5N - 2 bass reflex tubes HP 50 - 3 metres cable 2x2.5 mm2 - 1 pack polyester fleece (2 mats) - self adhesive foam sealing tape - a terminal with gold plated brass binding posts - 8 x screws PAN 4x20 - building instruction - the crossover components to be mounted on wood: - 2.7 mH ferrite core coil, < 0.33 Ohm - 0.47 mH air core coil / 1.0 mm - 18 mH core coil / 3,74 Ohm - 0.39 mH air core coil / 0.7 mm - 15 uF ELCO, non etched, 50V - 10 uF ELCO, non etched, 50V - 220 uF ELCO, etched, 63V - 5.6 uF MKP foil, 400V - 10 Ohm MOX4 resistor (brown black black) - 4.7 Ohm MOX10 resistor (yellow purple gold) - 5.6 Ohm MOX10 resistor (green blue gold) - 4.7 Ohm MOX4 resistor (yellow purple gold)
Our kit consists of:
Price for Hora without cabinet per unit: EUR 209,00
If you prefer to mount the crossover components on a universal PCB instead on wood, we recommend a 150x115 mm universal PCB. 2 PCB's per speaker are needed: price per PCB EUR 4,70
If you prefer higher quality components, instead of good quality standard components, we recommend:
Price for Hora, high end without cabinet per unit: EUR 219,00
The high end crossover consists of coils in series to the bass driver that have a lower impedance, and capacitors with higher dielectric strength.
Should you require less distortion and higher transparency then we recommend a better quality components: - MKP capacitors instead of ELCO, non etched - no distortion prone core coils in the signal path, but an almost 2 kg wire coil - and finally Damping 10 for the cabinet.
The crossover components of our ultra version: - 2.7 mH air core coil / 2 mm wire - 0.47 mH air core coil / 1.4 mm - 18 mH core coil / 3.74 Ohm - 0.39 mH baked varnish air core coil / 0.7 mm - 15 uF MKP capacitor - 10 uF MKP capacitor - 220 uF ELCO, etched, 100V - 5.6 uF Audyn MKP Plus - 10 Ohm MOX4 resistor (brown black black) - 4.7 Ohm MOX10 resistor (yellow purple gold) - 5.6 Ohm MOX10 resistor (green blue gold) - 4.7 Ohm MOX4 resistor (yellow purple gold)
Price for Hora, ultimo without cabinet per unit: EUR 285,00
When using a valve amp an impedance correction is needed. The correction is the same for the standard and high end version since the component quality hardly influences the sound quality. The impedance correction consists of: - 0.47 mH air core coil / 0.7 mm - 33 uF ELCO non etched - 6.8 Ohm resistor, 20 Watt
Price for Hora impedance correction per unit: EUR 8,50
Home Hobby HiFi Overview